Adhesive-Backed Hook & Loop
The adhesive decides the performance — so we match it to your substrate, not to a catalogue page.
Adhesive-Backed Hook & Loop — 20 mm, Clear Acrylic Adhesive
General-purpose acrylic adhesive on a paper liner, indoor use.
Adhesive-Backed Hook & Loop — 25 mm, Black Acrylic Adhesive
Standard adhesive width for signage, trim and cable routing.
Adhesive-Backed Hook & Loop — 38 mm, Black & White Acrylic Adhesive
Wider adhesive face for panels and display frames.
Adhesive-Backed Hook & Loop — 50 mm, Black & Red Acrylic Adhesive
High peel area for semi-permanent mounting indoors.
Adhesive-Backed Hook & Loop — 25 mm, Black & White Hot-Melt, High Tack
Hot-melt adhesive for immediate grab on textiles and foam.
Adhesive-Backed Hook & Loop — 50 mm, Black & White Hot-Melt, High Tack
Wide hot-melt grade for upholstery and foam-to-fabric bonds.
Adhesive-Backed Hook & Loop — 20 mm Black & White Release Liner
Release liner keeps the cut line visible on dark fabric.
Adhesive-Backed Hook & Loop — 25 mm, Black & White Die-Cut Dots
Kiss-cut dots on a sheet, peeled one at a time at the assembly line.
Adhesive-Backed Hook & Loop — 30 mm, Black Round Coin
Round coin for wall fixings, signage and removable mounting.
Adhesive-Backed Hook & Loop — 50 × 100 mm, White Square Pad
Rectangular pad for picture hanging and panel alignment.
Adhesive-Backed Hook & Loop — 100 mm, Black Wide Strip
Wide strip for carpet, matting and long edge runs.
Adhesive-Backed Hook & Loop — 25 mm, Orange LSE Grade
Formulated for polypropylene, polyethylene and powder-coated surfaces.
Adhesive-Backed Hook & Loop — 20 mm, Black / White / Silver Acrylic Adhesive
General-purpose acrylic adhesive on a paper liner, indoor use.
Adhesive-Backed Hook & Loop — 25 mm, Black & White Acrylic Adhesive
Standard adhesive width for signage, trim and cable routing.
Adhesive-Backed Hook & Loop — 38 mm, Black & White Acrylic Adhesive
Wider adhesive face for panels and display frames.
The models we quote most often
| Model / specification | What it is used for |
|---|---|
| AD-01 20 mm, Clear Acrylic Adhesive | General-purpose acrylic adhesive on a paper liner, indoor use. |
| AD-02 25 mm, Black Acrylic Adhesive | Standard adhesive width for signage, trim and cable routing. |
| AD-03 38 mm, Black & White Acrylic Adhesive | Wider adhesive face for panels and display frames. |
| AD-04 50 mm, Black & Red Acrylic Adhesive | High peel area for semi-permanent mounting indoors. |
| AD-05 25 mm, Black & White Hot-Melt, High Tack | Hot-melt adhesive for immediate grab on textiles and foam. |
| AD-06 50 mm, Black & White Hot-Melt, High Tack | Wide hot-melt grade for upholstery and foam-to-fabric bonds. |
| AD-07 20 mm Black & White Release Liner | Release liner keeps the cut line visible on dark fabric. |
| AD-08 25 mm, Black & White Die-Cut Dots | Kiss-cut dots on a sheet, peeled one at a time at the assembly line. |
| AD-09 30 mm, Black Round Coin | Round coin for wall fixings, signage and removable mounting. |
| AD-10 50 × 100 mm, White Square Pad | Rectangular pad for picture hanging and panel alignment. |
| AD-11 100 mm, Black Wide Strip | Wide strip for carpet, matting and long edge runs. |
| AD-12 25 mm, Orange LSE Grade | Formulated for polypropylene, polyethylene and powder-coated surfaces. |
| AD-13 20 mm, Black / White / Silver Acrylic Adhesive | General-purpose acrylic adhesive on a paper liner, indoor use. |
| AD-14 25 mm, Black & White Acrylic Adhesive | Standard adhesive width for signage, trim and cable routing. |
| AD-15 38 mm, Black & White Acrylic Adhesive | Wider adhesive face for panels and display frames. |
What this family is
Adhesive-backed hook and loop is laminated with a pressure-sensitive adhesive and a release liner. The three common systems behave very differently: acrylic for long-term outdoor and UV exposure, hot-melt for high initial tack on paper and board, rubber for low-surface-energy plastics.
Adhesion is only as good as the surface it lands on. We ask for the substrate, the service temperature and the expected load, then confirm with a test on your actual material before a production run.
Related constructions: Die-Cut Hook & Loop and Back-to-Back Strap.
Available options
- Acrylic, hot-melt or rubber adhesive
- Paper or film liner
- Kiss-cut pads and strips
- Custom die-cut shapes
Specification
| Material | Hook & loop + pressure-sensitive adhesive |
|---|---|
| Adhesive | Acrylic / hot-melt / rubber |
| Width | 10–100 mm |
| Colour | Black, white |
| Liner | Paper or film |
| Format | Rolls, strips, die-cut pads |
| MOQ | Confirmed with your quotation |
| Lead time | Confirmed with your quotation |
Typical applications
- Signage and display mounting
- Packaging and carton closure
- Furniture and trim fixing
- Screen and access panels
Adjacent constructions
Specifying Adhesive-Backed Hook & Loop
What widths can you supply in Adhesive-Backed Hook & Loop?
Standard supply runs 10–100 mm. Custom slitting and edge tolerance are confirmed on the quotation.
Which backing or format should I choose?
Available options are Rolls, strips, die-cut pads. The choice depends on the substrate and how the part is assembled; we test on your material before production.
Can you make Adhesive-Backed Hook & Loop to my drawing or sample?
Yes. We produce to an approved drawing or your own sample, including slit rolls, tabs and die-cut parts. Tooling, MOQ and lead time are confirmed with the quotation.
Send the drawing. We will tell you what will fail.
Width, colour, backing, quantity and the surface it has to stick to — that is enough to start.